Tile Adhesives and Grouts
Stainless GROUT

Weather resistant stainless non-sanded smooth tile jointing grout.

Grouting of walls and floors joints subjected to varying range of dry or humid conditions.
Compatible with Saveto tile adhesive range.
Suitable for use with most type of tiles such as Ceramic, Porcelain, Terrazzo, Marble Tile Joints
Fast Download
Technical Information
Product Description

Stainless Grout is a cementitious mortar adhesive composed of hydraulic binders, selected aggregates, polymer modified and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable mortar. Stainless grout eliminates the need for sealer. Stainless Grout is applied in thickness from: 2-4 mm for wall tiles and 3-8 mm for floors tiles.

  • Hydrophobicity properties for stain resistance, uniform colour & durability.

  • Factory controlled pre-blend ensures consistent high quality. 

  • Requires only addition of water on-site at the time of usage.

  • Easy tile installation that enables high Productivity. 

  • Superior workability. 

  • Excellent bonding on variety of ceramic tiles available in the local market.

  • Weather resistant.

  • Suitable for internal &  external applications.

  • Suitable for horizontal & vertical surfaces.

Compliance Standard
  • ISO 13007-3,4

  • ASTM C348 & C349

  • ISO 13007

  • BS: EN 13888

Packaging & Coverage

Stainless supplied in Grout 20 Kg Bag


  • Wall: 0.3 - 0.5 Kg/LM/3mm Joint
  • Floor: 0.5 - 0.8 Kg/LM/5mm Joint
Shelf Life & Storage

Original sealed container of Stainless Grout has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

White powder
Application Information
Instructions for use


For the preparation of Stainless Grout  mortar, pour into a container 6 -7  Liters of water for 20 Kg bag of Stainless Grout . Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water should be added. 

It can also be blended manually for small quantity but ensure correct amount of powder to water is maintained. 

If required, add 0.5Ltr of Saveto Bond 2 to the mixing water followed by addition of Stainless Grout powder.

Mixed material can be used within 1 hour. Do not add water to the mix, once the mortar adhesive starts to harden.


Spread the mixed mortar over the tile joints and firmly pressed with rubbing pad covered with sponge rubber spatula.

Stainless Grout  mortar is spread diagonally across the joints ensuring that the Stainless Grout  is pressed firmly into the joints.

Excess grout that remains on tiles shall be removed with same tool.

After initial setting of 20-30 minutes, depending upon the ambient temperature & humidity, clean the tiles and remove all excess material with a wet sponge.

After full drying, clean the tile surfaces with dry cloth or dispensable cotton towels.

When washing & drying the tiles, ensure tile joints are not rubbed too deep.

Stainless Grout  must be kept moist for first 2 days after application to ensure good hardened properties are achieved.


Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.

Surface Preparation

All excess adhesive tiles that are at the level higher than half of the tile thickness shall be removed.

All the joints should be free from dust, loose materials & traces of foreign materials etc. Neutralize the water absorption of the tiles by applying clean potable water.

Do not leave water pooling in the joints.

Additional Information
Health & Safety

Stainless Grout is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Stainless Grout is non-flammable.


Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Ceramic TILE FIX

Weather resistant cementitious adhesive for ceramic tiles.


Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.



Water resistant grout for swimming pool tile joints.


Porcelain TILE FIX

Polymer modified weather resistant adhesive for porcelain tiles.



High quality ceramic tile adhesive for projects.


view more
Featured Product
Vetoprime EP190

Versatile water based penetrating epoxy primer

As a universal versatile primer for water based resinous flooring and concrete repair systems.
Sealing of semi-porous cementitious substrates.
Priming of concrete slabs and walls to receive water-based epoxy, urethane, acrylic and hybrid coatings.
Priming of concrete substrates to receive epoxy and hybrid based repair mortars.
Priming of cementitious screeds to receive epoxy, urethane and resinous toppings.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map