Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.
Pool Fix is a cementitious mortar adhesive composed of hydraulic binders, selected aggregates and special additives . It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable mortar. Pool Fix is suitable to use as dry set fixing mortar particularly for Pool ceramic wall & floor tiles. Pool Fix is applied in thickness from 3mm to 10mm, depending upon type of tiles and quality of substrate.
Factory controlled pre-blend ensures consistent high quality.
Requires only addition of water on-site at the time of usage.
Superior bond in wet & immersed water conditions
Easy tile installation that enables high Productivity.
Superior workability.
Excellent Slip resistance.
Excellent Adhesion on variety of tiles available in the local market.
Suitable for internal & external applications
Suitable for horizontal & vertical surfaces.
BS:EN 12004 as C2TE S1
ISO 13007
ASTM C348 & C349
Pool Fix supplied in 25 Kg Bag
Coverage:
Walls: 6.5-7.0 m²/bag 25 kg
Floor: 5.0-5.5 m²/bag 25 kg
Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastages extra.
Original sealed container of Pool Fix has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Mixing
For the preparation of mortar adhesive, pour into a container 7.5-8 liters of water for 25 Kg bag of Pool Fix. Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water to be added.
It can also be blended manually for small quantity but ensure correct amount of powder to water is maintained.
If required, add 0.5Ltr of Saveto Bond 2 to the mixing water followed by addition of powder.
Mixed material can be used within 2 hours.
Do not add water to the mix, once the mortar adhesive starts to harden.
Application
Spread the mixed mortar adhesive and firmly pressed onto the surface to be tiled and work with notched trowel. Spread the mortar adhesive to an area that can be tiled within 10-15 minutes. Tiles are then firmly pressed over the mortar adhesive and immediately knocked into the desired position. Position of the tiles can be adjusted, if required, within its adjustability time of 10-15 minutes after installation. Allow the installed tiles to remain undisturbed for at least 48 hours.
Mortar adhesive must not rise higher in the joints than halfway the thickness of the tiles.
It is recommended to use Vetonit Pool Grout for filling the joint gaps after 2 days of tile installation.
Cleaning
Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.
The surface should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, etc.
Wet the all surfaces with clean water prior to the application of Pool Fix. Surface should appear damp with no water pooling.
Pool Fix is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Pool Fix is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather resistant cementitious adhesive for ceramic tiles.
Water resistant grout for swimming pool tile joints.
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
Water resistant premium quality ceramic tile adhesive
Saveto plaster accessories - plaster control joint