Flexible non-foaming polyurethane injection resin.
Vetogrout UR711 is a two part solvent-free, low viscosity, polyurethane resin system. When mixed in the proportions supplied reacts to form a tough, slightly flexible resin. Vetogrout UR711 has a good adhesion to concrete and masonry and when injected into cracks it allows some movement without loss of bond.
Used in conjunction with Vetogrout UR710 forms a permanent seal in cracked concrete.
- Vetogrout UR711 supplied 5 liter Kit. Theoretical Yield - 5 liter yield.
- Vetorep ER350 supplied in 1 & 5 kg Kits. Theoretical Yield - 1.7 kg/m2/mm.
- Vetonit Solvent XX400 supplied in 4 Liter cans. Theoretical Yield - 4 liter yield.
Vetogrout UR711 original sealed containers have a shelf life of 6 months @ 20ºC provided it is stored clear of ground in a dry shaded and temperature controlled conditions.
If stored at high temperatures and/or high humidity conditions the shelf life may be reduced to 2 to 3 months.
Vetogrout UR711 application
Thoroughly mix the entire hardener and base resin contents until the liquid becomes clear.
Vetogrout UR711 should be used with standard injection equipment having closed containers. The injection pressure should be at least 0.4 N/mm2 (4 bar).
Only mix sufficient resin that can be used within the pot life of the material.
Remove the packers or nipples. Make good any holes or voids with Vetorep ER350 and allow to cure. The Vetorep ER350 can be ground off or softened with a blow lamp and peeled off. Do not allow to burn.
Vetogrout UR711 and Vetorep ER350 should be removed from tools, equipment and mixers with Vetonit Solvent XX400 immediately after use. Hardened material can only be removed mechanically.
Clean the surface and remove any dust, unsound or contaminated material, plaster, oil, paint, grease, corrosion deposits or algae.
The surface should preferably be prepared using high pressure water jetting or light abrasive blasting, followed by thorough washing to remove dust and remaining particles.
Dirt alone may be removed with wire brushes or similar mechanical means. Oil and grease deposits should be removed by steam cleaning, detergent scrubbing or the use of a proprietary degreaser. The effectiveness of decontamination should be assessed by a pull-off test.
Blow the cracks and treated surface with oil free air to ensure complete removal of all dust and loose particles.
Ensure that the surfaces are blown dry.
In the presence of running water the flow must be stopped using Vetogrout UR710 which produces a rapid setting water-stopping foam (see separate data sheet). When the water is stopped the cracks are re-injected with Vetogrout UR711.
All cracks must be sealed and injection packers located in place before Vetogrout UR711 is injected.
Fixing injection packers
The injection packers inserted into pre-drilled holes shall be fixed at intervals along the length of each crack. The distance between each packer will depend upon the width and depth of the crack. Spacing shall be close enough to ensure that the resin will penetrate along the crack to the next point of injection. This will normally be between 200 mm to 500 mm.
The surface of the cracks between the packers shall be sealed with a band of Vetorep ER350, 30 mm to 40 mm wide and 2 mm to 3 mm thick. Both sides of any cracks which go all the way through a wall or slab shall be sealed in this way. In the case of a wall or slab which is cracked all the way through, packers shall be located on both sides with those at the back placed at midway points between those at the front.
The Vetorep ER350 shall be allowed to cure for 8 hours at 35ºC. At low ambient temperature (5ºC to 12ºC) the curing time will be extended and the applicator shall ensure that the surface sealant has adequately cured prior to continuing.
One end of the injection hose shall be attached to the lowest packer on vertical cracks or to either end of horizontal cracks.
Each crack shall be treated in a single, continuous operation.
Sufficient material shall, therefore, be made ready prior to the commencement of the work.
Vetogrout UR711 is designed to form a permanent flexible seal in cracked concrete and masonry units for widths between 0.2 and 10 mm.
It can also be used to stabilize soil and create membrane barriers behind retaining walls.
Vetogrout UR711 contains Isocyanate. May cause sensitization by inhalation. During use avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. The use of barrier creams provide additional skin protection.
Should accidental skin contact occur, remove immediately with a resin removing cream followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately - do not induce vomiting. Use only in well ventilated areas. In case of insufficient ventilation wear suitable respiratory protective clothing.
Vetogrout UR711 and Vetorep ER350 are not flammable. Vetonit Solvent XX400 is flammable, keep away from sources of ignition and direct flame.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Epoxy resin twin cartridge anchoring grout
Polyester injection and anchoring grout
Water based concrete curing compound
Multi-Purpose Acrylic Resin Curing Compound
Water based acrylic curing compound and primer *
Weather resistant stainless non-sanded smooth tile jointing grout.