Concrete Grouts, Repairs, & Enhancements
Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Retaining moisture in concrete after pouring.
Allowing concrete to cure efficiently as required by concreting practice.
General concrete curing application such as concrete slabs, retaining walls, runways, bridges, pavements...etc.
Where subsequent coating finishes are required without having to remove the curing compound.
As a penetrating primer on weak and porous cementitious surfaces prior to painting
Fast Download
Technical Information
Product Description

Vetocure XT426 is a resinous based curing compound for cementitious substrates that is designed to be used as a curing agent that allows subsequent application of cementitious* and acrylic renders. Vetocure XT426 is a clear liquid that is applied directly from the pail to the concrete substrate by spray equipment to achieve required results.
* It is recommended to remove the curing compound when applying cementitious renders.

  • Easy to use single component directly from the container.
  • Minimizes cracking potential.
  • Improved curing and cement hydration.
  • Sprayable.
  • High curing efficiency.
  • Ready to receive further renders (refer to detailed method statement or Saveto technical department).
Compliance Standard

ASTM C309 as Type I, Type 1-D and Type 2 Depending on color, class B.

Packaging & Coverage

Vetocure XT426 supplied in 20 Liter Pail / 200 Liters Drum and 1000 liter IBC tanks

Theoretical Coverage : 7-9 m2/Liter.

Shelf Life & Storage

Vetocure XT426 has a minimum shelf life of 12 months, provided the temperature is kept within the range of 5ºC to 35ºC. Freezing and prolonged exposure to heat or direct sunlight should be avoided. Should the temperature of the product fall outside this range then the Saveto Technical Service Department should be contacted for advice.

Containers should be kept sealed and airtight to prevent loss of moisture by evaporation.


Clear or white Liquid
Application Information
Instructions for use

Design Criteria

Vetocure XT426 is a resin based curing compound. When first applied to a fresh cementitious surface the product forms a continuous non-penetrating coating. This coating dries to form a continuous film which provides a barrier to moisture loss ensuring more efficient cement hydration, improved durability and reduced shrinkage.


Minimum application temperature: 5ºC

Vetocure XT426 white should be stirred before use to ensure even dispersion of the pigment.

Vetocure XT426 should be spray applied to the surface of fresh concrete. Application should begin immediately the concrete is free from surface water. Do not apply if bleed water is forming or present on the concrete surface.

The spray nozzle should be held approximately 450 mm and inclined at 35º to 45º from the concrete surface and passed back and forth to ensure complete coverage. The fugitive white color during application provides a guide to the area covered. Pump pressure should be maintained to give an even, fine spray.

After spraying, no further application of water or other material is necessary to ensure continued curing. The concrete surface should not be disturbed until it has sufficient strength to bear surface loads. The applied film should not be walked on before it is fully dry and care should be taken to ensure that the film is not broken.

Vetocure XT426 may also be applied to the surface of newly hardened concrete immediately after demoulding. In such cases the concrete surface must be damp and not dry. Dry surfaces may prevent correct film formation and cause absorption of the Vetocure XT426 which may lead to staining and difficulty in later removal. 

Theoretical Coverage rate
The recommended coverage rate is between 7 - 9 m2/liter. Coverage rates outside this recommended range may be used if necessary and suitable to meet specific requirements. Contact local Saveto office or representative for advance in such cases.

Spray equipment producing a fine mist may be used for Vetocure XT426. The suitability of equipment should be ensured by an application trial.

Equipment cleaning
Spray equipment should be cleaned immediately after use by flushing through with white spirit.

Over-coating and removal
Vetocure XT426 is ready to receive further layers of acrylic, polyurethane and bituminous base.

Additional Information
Health & Safety

Vetocure XT426 is flammable and should not be exposed to heat and direct sun light. Vetocure XT426 should not be swallowed or allowed to come into contact with skin and eyes either in bulk or spray form.
Suitable protective gloves and goggles should be worn. Splashes on the skin should be removed with water. In case of contact with eyes rinse immediately with plenty of water and seek medical advice. If swallowed seek medical attention immediately - do not induce vomiting.
For further information consult the Material Safety Data sheet available for this product.

Cleaning and disposal
Spillages of Vetocure XT426 should be absorbed onto sand, earth or vermiculite and transferred to suitable containers. Remnants can be cleaned with Vetonit Solvent XX400.
The disposal of excess or waste material should be carried out in accordance with local legislation.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT427

Water based acrylic curing compound and primer *

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

view more
Featured Product
Vetonit PBL

Saveto block reinforcement access-ories ladder type


As vertical bars to reinforce masonry block works
Reinforces block walls against wind effect.
Withstand the loading of material against the wall.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map