Flooring & Coatings Systems
Vetotop CS537

Premixed    20   to   100    mm   thick cementitious bonded screed.

• Leveling of concrete slabs prior to the application of final floor coverings.
• Screeding over hollow-core pre-cast concrete slabs.
Fast Download
Technical Data Sheet
download (*.pdf 0.18Mb)
Technical Information
Product Description

Vetotop CS537 is a single component cementitious bonded floor screed composed of hydraulic binders, silica sand, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, once mixed it will form a screed-able trowellable mortar that is applied in thicknesses between 20 and 100 mm.

  • Factory  controlled pre-blend ensures consistently high quality.
  • Suitable for Middle East harsh weather conditions.
  • Easy application enabling high productivity & superior finishing.
  • High bond to the substrate.
  • Excellent physical and mechanical properties. Shrinkage compensated.
  • Excellent workability.
Compliance Standard
  • EN197: 2011
  • EN13813:2002
  • BS8204:2010
  • ASTM C109
Packaging & Coverage


Pack Size


Vetotop CS537

50 Kg Bag

21.7 - 27.8 Ltr

Shelf Life & Storage

An original sealed bag of Vetotop CS537 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Surface Preparation

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.


Vetotop CS537 is a bonded screed that can be laid in thickness between 20 - 100 mm.

For more adhesion, an epoxy bonding agent can be used such as Vetobond EB430 or Vetobond EB431. Vetobond PB434 slurry can also be used.




   Product Data Sheet



To prepare the slurry primer mix 1 volume of Vetobond PB434 to 1 volume of clean water with 3 volumes of fresh cement and mix until a smooth consistency is achieved. Scrub the mixed slurry into the concrete surface, while the slurry is wet apply Vetotop CS537 in order to ensure good adhesion with the substrate.


For mixture preparation, pour into a container 4.5-5 liters of water for 50 Kg bag of Vetotop CS537.

Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle, until   a uniform, lump free consistency mix is achieved. No further water should be added to the mix. Do not add water to the mix once it starts to set.


Pour the mixed product onto the surface and spread to the desired thickness using steel trowel or suitable tools. Cover the screed with a plastic sheet to avoid drying.

Cure the screed as per standard concrete curing practices. Do not subject the screed to vehicular traffic for 28 days till ensure full cure and systems ability to withstand designed traffic loads.

A concrete sealer is required for enhancing the screed durability and resistance to ingress of water, apply Vetoseal XW770 at a rate of 8 to 12 m2 per liter. Make sure that the sealer is uniformly applied and covering all screed surface.


Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.

Additional Information
More Products from this section
Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Water Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

view more
Featured Product
Vetoflex PBR

Closed cell polyethylene backing rod

Controlling and filling gaps behind sealants
Prohibiting sealant bonding to joint fillers
Allowing joint sealant freedom of movement to achieve its desired function
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map