Elastomeric polyurethane liquid applied waterproofing membrane
Vetoproof UM766 is a premium quality pitch extended polyurethane waterproofing membrane, the product is liquid applied that hardens through reaction with atmospheric water vapour to form a highly elastic rubbery jointless membrane that is resistant to aggressive ground water and sewage. Vetoproof UM765 can be applied at 0.7mm on vertical application.
Vetoproof UM766 is supplied in 20 Liters Pails, Theoretical Coverage: 1.4m²/L @ 0.7mm thickness
Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.
Original sealed bag of Vetoproof UM766 has a shelf life of 6 months provided it is stored in original sealed containers clear of ground in a dry and shaded place below 35ºC.
Vetoproof UM766 use follows the guidelines of EN BS8102:2009 and CIRIA report No. 139 and ASTM guides C1417 nad 898.
Priming is not usually required on good quality concrete substrates. However, for highly porous or absorbent concrete use use Vetoseal XX777-50.
Vetoproof UM766 should be applied by brush, trowel or a gaged spreader at a thickness of 0.7mm. Glass fiber scrim and joint tapes can be used on corners and critical areas for reinforcement of the membrane.
Tiling over Vetoproof UM766 is possible, in such cases sharp sand needs to be sprayed over Vetoproof UM766 while still wet, 24 hours later all excess sand is to be removed and a suitable tile adhesive from Saveto range can be used to bond the tiles directly over the membrane.
Vetoproof UM766 must be allowed to cure for a minimum of 24 hours prior to placing protection. Where damage to the membrane is possible; the membrane needs to be protected by a cementitious screed or protection boards.
Note: Vetoproof UM766 is not resistant to UV light.
All tools employed for the application of Vetoproof UM766 can be cleaned with Vetonit Solvent XX400 before it hardens otherwise mechanical means are needed.
All surfaces where Vetoproof UM766 has to be applied must be clean and have an open capillary system. Eliminate laitance, dirt, grease and other loose materials by means of high pressure water jetting or wet sand blasting. Defective concretes such as cracks and honeycombs, etc. has to be chased out and repaired prior to the application.
Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetoproof UM766 is flammable, do not use near to open flames. Refer to product MSDS for further information.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Single component acrylic waterproofing membrane
Single component elastomeric crack-bridging cementitious waterproof membrane
Single component flexible pure acrylic waterproofing membrane
Polymer modified water resistant cementitious top coat
Single component penetrating waterproofing system for concrete
Water Resistant Patch & Repair Premixed Render