Flooring & Coatings Systems
Vetotop EC698

Solvent free high performance, high build epoxy flooring system

Floor coating for a variety of industrial applications such as: production assembly areas, workshops, dairies, bottling plants, breweries, pharma plants, kitchens, showrooms, etc.
Anti-slip floors, ramps & high traffic.
Wet working areas.
Floor coating for car-parking.
Fast Download
Technical Information
Product Description

Vetotop EC698 is a two component high performance solvent free epoxy coating system designed for the protection of concrete floors. Once cured, the product has excellent abrasion and good chemical resistance. Vetotop EC698 provides an attractive hard wearing and easily cleanable floor finish. 

  • High abrasion and impact resistance.
  • Ease of application.
  • High chemical resistance.
  • Low maintenance costs.
  • Hygienic, impervious and easily cleanable.
  • Slip-resistant finish can be obtained.
  • Available in 8 standard colors with possibility of custom RAL colors.
  • High bond, stronger than concrete cohesive strength.
  • Economic installation.
Compliance Standard

BS EN476:2009 as class 1 in flame spread.

Packaging & Coverage



Pack Size

Theoretical Coverage

Vetotop EC698

4 & 15 Liter Kits 

5 m2 / Liter @ 200 µm

Vetoprime EP691

4 Liter Kits

8 m2 / Liter

Vetoprime EP490

4 Liter Kits

8 m2 / Liter

Antislip Aggregates

25 Kg Bags


In case of use of antislip aggregates; the consumption values for the top coat will increase by 15 to 20%. Antislip aggregate consumption:



Antislip Aggregate Fine

1.5 - 3.5 m2 / Kg

Antislip Aggregate Medium

1.2 - 3.0 m2 / Kg

Antislip Aggregate Coarse

1.0 - 3.0 m2 / Kg


Total System Thickness with antislip aggregate use:

Vetotop EC698 with Antislip Aggregates Texture



0.75 - 1.5 mm


1.5 - 2.0 mm


2.0 - 2.5 mm

Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.

Shelf Life & Storage

Original sealed bag of Vetotop EC698 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Available in 8 standard colors with possibility of custom RAL colors.
Application Information
Instructions for use

Design Criteria

Vetotop EC698 is designed to be a hard wearing two coat application on cementitious substrates. The applied product will be resistant to water as well as a wide range of chemicals.


If concrete surface is porous, or w/c ratio is >0.5 it is recommended to use Vetoprime EP691 as a film-forming primer or EP490 as a penetrating primer for porous substrates.

Vetoprime EP691 should be mixed in the proportions supplied. Add the entire contents of the hardener can to the base can. When thoroughly mixed, preferably using a slow speed mixer, the primer should be applied in a thin, continuous film using rollers or stiff brushes. Work the primer well into the surface of the concrete taking care to avoid ponding or over application. The primer should be left to achieve a tack-free condition before applying the top coat.

Mixing Vetotop EC698

In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Dilution up to 8% using Veto Solvent XX600 to aid application is permitted.


The application and cure temperature must be above 15°C. The first coat of Vetotop EC698 should be laid using a short haired lamb wool roller, or gauged squeegee to achieve a continuous coating. Ensure that loose hairs on the roller are removed before use. A minimum film thickness of 150 microns per coat should be applied for flooring system (this can be increased where specifications demand). The top coat can be applied in the same manner within 8 to 24 hours of the application of the top coat.

Antislip Aggregates

If the option of using Vetograin antislip aggregates has been chosen, the base coat should be dressed with the chosen antislip aggregates as soon as possible after laying of the base coat. The recommended procedure is to completely blind the base coat i.e. apply excess dressing aggregate to completely obliterate the base coating.

Alternatively, the antislip silica particles can be broadcast in a light random dressing to provide a less dense finish, or the product can be used to obtain a smooth finish by omitting the antislip aggregates.

When the base coat has reached initial cure (after 12 hours at 20°C or 5 hours at 35°C), the excess aggregate should be vacuum cleaned from the surface.

The top coat can now be applied by a short haired roller or airless spray equipment. Care should be taken to ensure that a continuous film is achieved and the rough surface caused by the aggregate is completely sealed. This topcoat must be applied within 36 hours at 20°C (15 hours at 35°C) of the application of the resin base coat.

Expansion Joints

Expansion joints in the existing substrate must be retained and continued through the Vetotop EC698 topping. Saveto have a range of joint sealants specifically designed for flooring (see Vetoflex PS781, Vetoflex PS782 and Vetoflex PS786 product data sheets).


Tools and equipment should be cleaned with Vetonit Solvent XX600 immediately after use.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc. 

Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range. 

New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Additional Information
Health & Safety

Vetotop EC698, Vetoprime EP691, Vetoprime EP490 and Vetonit Solvent XX600 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used.

The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetoprime EP490 and Vetonit Solvent XX600 are flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam. 

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Water Based Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

view more
Featured Product
Vetonit Ultra

Polymer modified weather resistant multipurpose adhesive for tiles.


For Ceramic tiles, natural stone conglomerates (Granite & Marble, Terrazo) , artificial stone and large format tiles.
Tiling on smooth concrete surfaces, lightweight bricks, blocks, plaster boards.
Tiling on wall surfaces that are plastered with water resistant plasters such as Vetonit Render & Vetonit Base WR on damp concrete interiors.
Suitable for dry & wet conditions.
Suitable for tile on existing tile applications.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map