Bahrain
Egypt Jordan Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Primers and Ancillary
Vetoprime EP390

Versatile solvent free epoxy based primer

Uses
As an industrial grade primer for resinous flooring and concrete repair systems.
As a primer on damp concrete.
Sealing of highly porous cementitious substrates.
Fast Download
Technical Data Sheet
download (*.pdf 0.15Mb)
Method Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetoprime EP390 is a specialty industrial primer for the Vetorep and Vetotop product range, its applied on prepared concrete, cementitious and steel substrates to seal the substrate and enhance bonding with top coats. The product can be used as a stand alone product in internal applications as a seal coat to harden cementitious surfaces and prevent dusting. Vetoprime EP390 is a two component solvent free epoxy resin that has sealing properties making it ideal for concrete substrates.

Advantages
  • Easily applied by brush, roller or spray.
  • Versatile with applications in a large number of coating materials and sealants.
  • Can be applied on damp concrete.
  • High wetting properties.
  • Damp tolerant.
  • Perfect for use with epoxy, urethane repairs, screeds and self smoothening toppings.
  • Cost effective, suitable for use in MENA region conditions.
Packaging & Coverage

Vetoprime EP390 is supplied in 1 & 4 Liter kits, coverage:7 - 10 m2 /Liter

Shelf Life & Storage

Original sealed container of Vetoprime EP390 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Colors
Transparent Yellowish Liquid
Application Information
Instructions for use

General Applications

  • Priming of joint edges to receive urethane, epoxy, and polyurea based sealants.
  • Priming of concrete slabs and walls to receive solvent free epoxy, urethane, MMA, polyurea, hybrid coatings, screeds and self smoothening toppings.
  • Priming of concrete substrates to receive epoxy and urethane based repair mortars.
  • Priming of cementitious screeds to receive epoxy, urethane and resinous toppings.
  • Priming of steel substrates

Priming
Mix Vetoprime EP390 as supplied. Add the entire content of hardener can to the base can and mix thoroughly for about 2 minutes. Once mixed, the Vetoprime EP390 shall be immediately applied in a thin continuous film using stiff brushes or rollers. Avoid over-application and puddles.
Vetoprime EP390 shall be allowed to become tack-free prior to the application of epoxy coating (unless otherwise specified) but well within the open time specified for the given temperature.
The hotter the substrate, the more quickly the primer will become dry.

Cleaning
All tools and equipment shall be cleaned immediately after use with Vetonit Solvent XX400.

Surface Preparation

It is essential that Vetoprime EP390 is applied to a sound, clean and dry surface in order to achieve maximum bond strength between substrate and coating/repair products.

Concrete Substrates
Should be at least 28 days old and relative humidity of the concrete is 75% or below. Laitance deposits on new concrete are best removed by light grit blasting, mechanical scrabbling or grinding.
Where heavy contamination by oil and grease has occurred or existing coatings are present, it is essential that all contaminations are removed.

Additional Information
Health & Safety

Some people are sensitive to epoxy resins; so gloves and a barrier cream shall be used when handling these products. If contact with the resin occurs, it must be removed, before if hardens, with resin removing cream follow by washing with soap and water. Do not use solvent.
During use, avoid inhalation of solvent and contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. In case of contact with eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.
Vetoprime EP390 is non-flammable.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond

Multi-purpose bonding agent & admixture

Saveto Bond 2

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Vetonit PCJ

Saveto plaster accessories - plaster control joint 

 

Uses
Designed to deal with normal initial stucco shirinkage during the hydration and curing stage of cement stucco coats.
Controls plaster thermal expansion and contraction.
For walls and ceilings, and joints.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.