Primers and Ancillary
Vetonit Bond Pure

Multipurpose bonding agent & admixture

Works as admixture with plaster, lime/sand cement screeds, renders, mortars and cement grouts when diluted 1:7 with potable water.
Works as bonding agent and can be sprayed or brushed on green substrates to improve bonding of plasters, patching compounds. Renders, mortars, joint tape fixing etc. when diluted 1:3 with potable water.
Can be used for both internal and external applications.
Fast Download
Technical Information
Product Description

Vetonit Bond  Pure  is  a  single  component  polyvinyl  acetate based, admixture & bonding agent for cementitious materials. It is a water based, with thixotropic effect, specially formulated to enhance bonding properties as well as improve mechanical strengths of cementitious mixes when incorporated with mixing water. Vetonit Bond Pure also reduces shrinkage cracks during early stages of cement hardening by minimizing surface water loss in fresh applied mixes. Vetonit Bond Pure can be diluted on site with potable water for desired applications.

  • Multipurpose usage.
  • Can be used as bonding agent & admixture.
  • Enhances bonding of plaster, sand/cement screed, render etc.
  • Improves hydration & curing when added to cement based mixes.
  • Improves compression strength & abrasion.
  • It adheres well to various construction materials, including concrete, stone, etc.
  • Ensure brighter & long lasting colour to architectural finishes.
  • Reduces shrinkage & cracks.
Compliance Standard
  • ASTM C932
  • BS 6319
Packaging & Coverage

Vetonit Bond Pure is supplied in 20 & 120 Liter Containers, Coverage:30 - 40 m²/Ltr as bonding agent

Shelf Life & Storage

Original sealed container of Vetonit Bond Pure has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Milky white Viscous liquid
Application Information
Instructions for use

Vetonit Bond Pure is a highly concentrated material. Make sure the correct dilution ratio is followed to avoid stiff & fast drying mixture. Follow the dilution ratio required for each type of premixed mortar.

As Admixture
Dilute 1 part Vetonit Bond Pure with 7 parts water. Mix thoroughly to obtain uniform consistency liquid.
Add the diluted Vetonit Bond Pure to pre-blended sand/cement plaster, mortar, or other dry mixes. Mix for 3-4 min using mechanical mixer at low speed. Let the mixture stand for 10 min and mix again briefly to achieve homogeneous lump free mixture.

As Bonding Agent
Dilute 1 parts Vetonit Bond Pure with 3 parts water. Mix thoroughly to obtain uniform consistency liquid.
Apply using brush or spray directly onto substrate. If using hand pump, spray at a rate of 15 m2/litre. While bonding agent is still wet, follow immediately by applying plaster, render, mortars or joint tapes etc.

Note: Vetonit Bond Pure should remain tacky when applying top coat finishes.

Surface Preparation

Surface  must  be  well  cleaned  and  free  from  loose materials. Inconsistent parts, varnishes, grease, laitance, algae, must be eliminated through sand blasting or brushing before applying Vetonit Bond Pure.


Use the whole material once you opened the pack as the material start to skin & then dry.
Do not mix with other materials. Do not apply the product at temperature less than +7ºC.
Tools should be cleaned with water before it hardens. After the hardening its residuals can be removed mechanically only.
For further information contact our technical department.

Additional Information
Health & Safety

Vetonit Bond Pure is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise.
Ensure adequate ventilation when using the material and avoid inhalation of vapours.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond

Multi-purpose bonding agent & admixture

Saveto Bond 2

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Vetogrout ER717

Low viscosity epoxy grout & injection resin

Restoration of structural integrity of structural elements
Injection of structural elements in retaining walls, beams, columns, shear walls, tanks, etc.
Grouting and static crack filling from 0.2 to 10 mm
Base plate grouting in dynamic load situations
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map