Renders & Finishes
Vetonit Base WR

Weather Resistant Premix Cement Coating for Internal Use

Can be applied internally onto walls & ceiling surfaces.
On concrete surfaces that are smooth and also on precast concrete surfaces.
On wall surfaces that are plastered with water resistant plasters, Vetonit Renders and on damp concrete interiors.
Fast Download
Technical Information
Product Description

Vetonit Base WR  is a cement based coating composed of hydraulic binders, selected aggregates and special additives. It is supplied as a dry powder in a pre-weighed bags ready to use on site, which required only addition of clean water to produce easily workable mortar. Vetonit Base WR is a high quality product for multipurpose use and as a base coat for Vetonit Finish WR. Vetonit Base WR  can be applied in thickness from 1 mm to 5 mm, in one or two layers depending site requirement. Vetonit Base WR is available in two standard colours white, Grey & Saveto standard colours.

  • Factory controlled pre-blend ensures consistent high quality.
  • Requires only addition of water on-site at the time of usage.
  • Manual or spray machine application.
  • Superior workability.
  • Easy application that enables high Productivity.
  • Excellent Adhesion on variety of substrates.
  • Water resistant.
  • Suitable for humid & dry conditions.
  • Suitable for vertical & ceiling surfaces.
Compliance Standard
  • BS:EN 1015 - 12 (per BS EN 998)
  • ASTM 109
  • BS EN413-2
Packaging & Coverage

Vetonit Base WR is supplied in 25kg Bag or Bulk, with Yield: 1.0 - 1.2 Kg /m2 / 1mm thickness

Shelf Life & Storage

Original sealed bag of Vetonit Base WR has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place.
Vetonit Base WR is non-flammable.

White, Grey & coloured Powder
Application Information
Instructions for use

Internal Block Walls & Rough Surfaces
For manual application add to the mixing container 7.5-8.5 litres of water for each 25 Kg bag of Vetonit Base WR. For Spray machine application use 9.5-10.0 litres of water for each 25 kg bag. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water should be added.

Smooth Concrete Surfaces
Add 0.5 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as described above.
Mixed material can be used within 2 hours. Do not add water to the mix once the mixed mortar start to harden.

Vetonit Base WR can be applied in one or two layers as required to achieve desired thickness of 1-5 mm.
Various grades of finish textures can be obtained by selecting appropriate spray machine nozzle sizes.
Allow the installed application to remain undisturbed for at least 48 hours.

Vetonit Base WR is best cured by spraying water on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. This will help in achieving uniform colour, minimize risk of surface cracks and high mechanical strengths.

Surface Preparation

The surface should be sound, clean free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Vetonit Base WR application, wet the entire surfaces with clean potable water and surface should look damp at the time of Vetonit Base WR application.

  • Do not mix with any additives or products, unless recommended by Saveto.
  • Make sure the substrate is suitable for plaster coat application. In case of doubt, try on sample area to assess its suitability.
  • Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also excessive air-draught during initial curing stage.
  • Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
  • For further information contact our technical department.
Additional Information
Health & Safety

Vetonit Base WR is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately washed with copious amount of clean cold water. Seek medical advise.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetonit Crack Filler

High quality premixed surface crack filler


Water resistant internal use premix smooth cement coating


Water resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

Vetonit Putty WR

Water resistant high quality premixed putty

view more
Featured Product
Vetorel XT422

Chemical mold and form-work release Concentrate

Vetorel XT422 is used after dilution for the treatment of wooden and metal form work or molds prior to the casting of concrete to facilitate form stripping
Minimizing concrete surface blemishes and pinholes
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map