UV Resistant Pigmented Premixed Textured Plaster
Vetotouch Monocouche is a cement based plaster coat composed of hydraulic binders, selected aggregates special pigments and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mortar. Vetotouch Monocouche is a high quality product and suitable for external applications with marble chips.
Vetotouch Monocouche supplied in 50 Kg Bag or Bulk. Yield - 30 Liters.
Original sealed container of Vetotouch Monocouche has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Mixing
For manual application add to the mixing container 7.5-9 litres of water for each 50 Kg bag of Vetotouch Monocouche or 9-10.5 litres/50 kg bag for machine application. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Leave the mixed material to stand for 10 min and briefly remix without addition of water.
Smooth Concrete Surfaces
Prepare the smooth concrete Scarface by applying Vetonit Spatter Dash SB.
For better adhesion to the substrate, add a 0.5 Litter of Vetonit Bond 2 to the mixing water for each 50 Kg bag or add 1 liter of Vetonit Plastering Bond to the mixing water referenced to the measured powder quantity. then follow the same mixing procedures as described above.
Mixed material must be used within 1 hour. Do not add water, once the mixed mortar start to harden.
Application
Vetotouch Monocouche can be applied in a single or two coats on rough or smooth surfaces by manual or machine application to achieved desired thickness 3-20 mm.
Apply mixed material using spray machine or hawk & trowel technique. Rod or screed to uniform thickness, not exceeding 20 mm for single coat or 10 mm each coat for multiple layers. First layer should be pressed hard against the surface.
For second layer allow the first layer to partially set (60-120min depending on weather). Apply second layer as described above.
Water spray the surface if second layer is carried out next day.
Curing
Vetotouch Monocouche is best cured by spraying water evenly on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths.
Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Vetotouch Monocouche, wet the entire surfaces with clean potable water and surface should look damp at the time of Vetotouch Monocouche application.
Vetotouch Monocouche is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of cold water. Seek medical advise.
For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Advanced modified cementitious thermal insulating plaster
Advanced modified cementitious light weight, thermal insulating masonry mortar
Cementitious based adhesive and base coat for EIFS / ETICS
Cementitious based adhesive and base coat for EIFS / ETICS
Advanced Modified Cementitious Thermal Insulating Plaster
Water resistant premium quality ceramic tile adhesive
Cementitious Scratch / Key Coat