Tile Adhesives and Grouts

Weather resistant multipurpose sanded grout for jointing tiles.


Grouting of walls and floors joints subjected to varying range of dry or humid conditions.
Compatible with Saveto tile adhesive range.
Suitable for use with most type of tiles such as Ceramic, Porcelain, Terrazzo, Marble Tile Joints
Fast Download
Technical Information
Product Description

Vetonit Tile Grout is a cementitious polymer modified tile grout composed of hydraulic binders, selected aggregates, special additives, and polymers. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar. Grout is ideal for jointing of Ceramic Tiles, Terrazzo Tiles. Marbles. Tile Grout is available in white and grey, also available in other colors and different packing. Tile Grout is applied in a thickness of 2-4 mm for wall tiles and 3-8 mm for floor tiles.”

  • Factory controlled pre-blend ensures consistent high quality. 

  • Requires only addition of water on-site at the time of usage.

  • Easy tile installation that enables high Productivity. 

  • Superior workability. 

  • Excellent bonding on variety of tiles available in the local market.

  • Water & weather resistant

  • Suitable for internal &  external applications

  • Suitable for horizontal & vertical surfaces.

Compliance Standard
  • BS:EN 13888
  • SASO ISO 13007-3,4 as CG2AW

Packaging & Coverage

Tile Grout supplied in 5, 10, 20, 25 kg Bag


  • Wall: 0.3 - 0.5 Kg/LM/3mm Joint
  • Floor: 0.5 - 0.8 Kg/LM/5mm Joint



Shelf Life & Storage

Original sealed container of Tile Grout has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colored Powder
Application Information
Instructions for use


For the preparation of Grout mortar, pour into a container 6.3-7.0 liters of water for each 20 Kg bag or 8-9 Litres for 25 Kg bag of Tile Grout. Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water to be added. 

It can also be blended manually for small quantity but ensure correct amount of powder to water is maintained. 

If required, add 0.5 Liters of Saveto Bond 2 to the mixing water followed by addition for each 20 kg bag of powder.

Mixed material can be used within 1 hour. 

Do not add water to the mix, once the mortar adhesive starts to harden.


Spread the mixed mortar over the tile joints and firmly pressed with rubbing pad covered with sponge rubber spatula.

Grout mortar is spread diagonally across the joints ensuring that the Grout is pressed firmly into the joints.

Excess grout that remains on tiles shall be removed with same tool.

After initial setting of 20-30 minutes, depending upon the ambient temperature & humidity, clean the tiles and remove all excess material with a wet sponge.

After full drying, clean the tile surfaces with dry cloth or dispensable cotton towels.

When washing & drying the tiles, ensure tile joints are not rubbed too deep.

Grout must be kept moist for first 2 days after application to ensure good hardened properties are achieved.


Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.

Surface Preparation

All excess adhesive tiles that are at the level higher than half of the tile thickness shall be removed.

All the joints should be free from dust, loose materials & traces of foreign materials etc. Neutralize the water absorption of the tiles by applying clean potable water.

Do not leave water pooling in the joints.

Additional Information
Health & Safety

Tile Grout is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Tile Grout is non-flammable.


Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Ceramic TILE FIX

Weather resistant cementitious adhesive for ceramic tiles.


Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.



Water resistant grout for swimming pool tile joints.


Porcelain TILE FIX

Polymer modified weather resistant adhesive for porcelain tiles.



High quality ceramic tile adhesive for projects.


view more
Featured Product
Vetotop UC372

High performance, matt finish chemical, scratch & UV resistant polyurethane floor & wall coating

long term protection of car parks and floors in factories, warehouses, laboratories, loading decks ramps, showers, kitchens, dairies, breweries.
UV Resistant top coat over flooring systems including concrete, epoxies, aromatic elastic polyurethanes,...etc.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map