Plasters & Renders
Spatter Dash LB

Weather resistant premixed key coat for AAC surfaces

Uses
Internal & external scratch coat for plasters
On AAC block units and walls.
Plaster bond enhancer and mechanical key on horizontal, vertical and overhead application
Fast Download
Technical Data Sheet
download (*.pdf 0.32Mb)
Catalogues
Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
Technical Information
Product Description

Spatter Dash LB a cement based coat composed of hydraulic binders, selected aggregates, and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable mortar. Spatter Dash LB is a high quality product for multipurpose applications such as scratch coat on highly absorbing surfaces and ceilings such as AAC, thermalite & calcium silicate.

Advantages
  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Manual or spray machine application or by hawk & trowel techniques
  • Superior workability
  • Easy application with uniform work flow enables high productivity & superior finishing
  • Excellent adhesion on variety of substrates
  • Internal & external applications
  • Weather resistant
  • Suitable for humid & dry conditions
  • Suitable for vertical & ceiling
Compiliance Standard
  • BS:EN 998-1
  • ASTM C 348, ASTM C 349, ASTM C 897 & ASTM C 926
  • ASTM C150 Type 1
Packaging & Coverage

Spatter Dash LB supplied in 50 Kg Bag or Bulk. Yield - 1.8 Kg / m2 /mm thickness

Shelf Life & Storage

Original sealed container of Spatter Dash LB has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
Grey
Application Information
Instructions for use

Mixing

Add to the mixing container 9.5-11.5 liters of water for each 50 Kg bag of Spatter Dash LB. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.

Application

Spatter Dash LB preferably be applied in a single coat application to achieved desired thickness of 4-6 mm.
Apply mixed material using mechanical spray or manual spatter machine or hawk & trowel technique.
Cover 95-100% of surface area to be plastered.
Allow the installed application to remain undisturbed for at least 48 hours.

Curing

Spatter Dash LB is best cured by spraying water on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitence, dirt curing compound, or any other substance that might impair the quality of bond with the substrate. Prior to Spatter Dash LB SDL211 Application, soak the entire surfaces with clean potable water. The substrate should be saturated surface dry at the time of Spatter Dash LB application.

Limitation

Make sure the substrate is suitable for the application of Spatter Dash LB, in case of doubt, try on sample area to assess its suitability. Do not apply the product under direct rain, extreme wind, and at temperatures below +5ºC or above +45ºC.

Additional Information
Health & Sefety

Spatter Dash LB is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Spatter Dash LB is non-flammable.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic PLASTER

High quality light weight premixed acoustic plaster

Plaster Gypsum

High quality light weight gypsum plaster

Plaster Gypsum PERLITE

Thermal insulation llight weight gypsum perlite plaster

Plaster Cement PERLITE

Sprayable premixed plaster

Premix Plaster S

Sprayable premixed plaster

view more
Featured Product
Vetofill CG550

Professional grade cementitious fine tile grout

Uses
Filling tile joints virtually all types of tiles up to 10 mm
Filling glass blocks joints
Commercial and residential buildings such as shopping malls, office buildings, palaces and mansions.
Wet areas such as kitchens, bathrooms and swimming pools
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map