Plasters & Renders
Plaster Gypsum

High quality light weight gypsum plaster

Internal plaster on block walls and rough surfaces
Plastering on fairfaced concrete and precast panels subsequent to Spatter Dash SB scratch coat
Improving thermal resistance properties as well as sound dampening
Fast Download
Technical Data Sheet
download (*.pdf 0.27Mb)
Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
reference projects
Al Waseel Hills
Saudi Arabia
Housing project
Technical Information
Product Description

Plaster Gypsum is composed of a retarded gypsum, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mix. Plaster Gypsum is a high quality product and provides very smooth surface as underlayment for paints, decorative coatings & wallpapers.

  • Factory controlled pre-blend ensures consistent
  • high quality
  • Requires only addition of water on-site at the time of usage
  • Can be applied by plastering machine
  • Single coat application with improved workability
  • Easy application with uniform work flow enables high productivity & superior finishing
  • Strong adhesion on variety of substrates
  • Acoustical properties
  • Very smooth finish can be achieved
  • Light weight plaster
  • Suitable for normal humid & dry conditions
Compiliance Standard
  • ASTM C28
  • ASTM C472
Packaging & Coverage

Plaster Gypsum supplied in 35 Kg Bag or Bulk. Consumption : 1.75 Kg /m2 / 1mm thickness

Shelf Life & Storage

Original sealed bag of Plaster Gypsum has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place.

White Powder
Application Information
Instructions for use

Smooth Concrete Surfaces

Add 0.5 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 35 kg bag. Follow same mixing procedure as above. Mixed material must be used within 30 minute. Do not add water once the mixed plaster mortar start to stiffen or hardened.


Plaster Gypsum is generally applied in a single coat method. Use directly on block walls & rough surfaces. On smooth concrete surfaces apply first a primer coat of Vetonit Bond 2. Apply mixed material using spray machine or trowel technique to cover the area to desired thickness. Lightweight leveling tools are required in conjunction with trowel to fill in holes.
When the plaster stiffens lightly, treat the surface to a smooth level to eliminate all traces of protrusions and undulations.
Let the plaster set for about 30 min., using wet sponge, wipe the surface to a creamy smooth finish.
Apply Vetocoat Finish WR white mixed with 0.5 Ltr of Vetonit Bond 2 at 2 mm thickness prior to application of decorative paints


Let the Plaster Gypsum to fully dry itself. Do not use water.
Paints & Coatings can be applied once the plaster and Vetonit Finish WR has dried out completely, generally after 7 days.

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc .Prior to Plaster Gypsum application, wet the entire surfaces with clean potable water and allow to dry prior to Plaster Gypsum application.


Do not mix with any additives or products, unless recommended by Saveto.
Make sure the substrate is suitable for plaster coat application. In case of doubt, try on sample area to assess its suitability. Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also excessive air-draught during initial curing stage. Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
For further information contact our technical department.

Additional Information
Health & Sefety

Plaster Gypsum is alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic PLASTER

High quality light weight premixed acoustic plaster

Plaster Gypsum PERLITE

Thermal insulation llight weight gypsum perlite plaster

Plaster Cement PERLITE

Sprayable premixed plaster

Premix Plaster S

Sprayable premixed plaster

Premix Plaster SF

Fiber reinforced sprayable premixed plaster

view more
Featured Product
Vetoproof AM764

Single component ultra flexible acrylic waterproofing membrane

Waterproofing of concrete, asbestos, metal,cement and gypsum board surfaces
Protecting spray-PU membranes from UV rays
As a decorative overlay on bituminous membranes and over existing terrazzo tiles
Waterproofing of corrugated sheet and sloped roofs
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map