Primers and Ancillary
Vetobond AB432

Acrylic polymer cement modifier & bonding agent

Uses
Enhancement of renders, floor toppings and plasters
As a primer for bonding cementitious repair materials (Vetorep range of products)
As a primer for renders and plasters on fairfaced concrete and gypsum boards
As a curing membrane, ready to receive further cementitious renders by re-priming
Fast Download
Technical Data Sheet
download (*.pdf 0.21Mb)
Method of Statement
download (*.pdf 0.65Mb)
Technical Information
Product Description

Vetobond AB432 is an acrylic polymer based bonding agent and cement modifier that is designed to be used as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application. Vetobond AB432 is a milky liquid that first turns purple when first applied on concrete then becomes clear once it dries, its applied directly from the bottle or pail to the concrete substrate by brush, roller or spray.

 

Advantages
  • Adhesive bond to concrete will always exceed the tensile strength of the host concrete
  • Suitable for use on damp and dry concrete
  • Environmentally friendly water-based odorless and non-flammable
  • Resistant to hydrolysis, used externally and internally
  • High mechanical properties, allows thin section applications
  • Excellent bond to concrete, masonry, stonework, plaster and cement boards
  • Cost effective, suitable for use in MENA region conditions
Packaging & Coverage

Vetobond AB432 supplied in 5 & 20 Liter Containers,

Coverage - 7 m2 /L as a primer

                 6 m2 /L as a curing aid

Shelf Life & Storage

Original sealed container of Vetobond AB432 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Colors
Milky liquid
Application Information
Instructions for use

Application of Bonding Aid

The substrate should be thoroughly soaked with clean water with any excess removed prior to commencement of the works. Scrub Vetobond AB432 into the substrate, avoid puddling and remove any excess. The repair mortar or topping should be applied whilst the primer is still tacky.

Mix Design

OPC - 50 kg
Sharp Sand#60 - 150 kg
Vetobond AB432 - 10 Liters
Water - Enough to give workable consistency

Curing

Cure the repair mortar or topping using Vetobond AB432 to prevent rapid loss of water. In severe drying conditions additional curing methods may be necessary. Protect uncured mortar from frost and rain.

Cleaning

Vetobond AB432 should be removed from tools, equipment and mixers with clean water immediately after use. Cured material can only be removed mechanically.

Surface Preparation

Clean all surfaces and remove any dust, unsound material, plaster, oil, paint, grease, corrosion deposits or algae. Roughen the surfaces, remove any laitence and expose aggregate by light scabbling or grit-blasting.

Limitation

Vetobond AB432 mortars, toppings and renders should not be used when the temperature is below 5°C and falling. Neither should they be exposed to moving water during application. Exposure to heavy rainfall prior to the final set may result in surface scour.

Additional Information
Health & Sefety

Cementitious mortars and slurries modified with Vetobond AB432 contain cement powders which, when mixed or become damp, release alkalies which can be harmful to skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond

Multi-purpose bonding agent & admixture

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

Vetobond EB431

Water dispersible epoxy bonding agent to bond old to new concrete

view more
Featured Product
Plaster Gypsum

High quality light weight gypsum plaster

Uses
Internal plaster on block walls and rough surfaces
Plastering on fairfaced concrete and precast panels subsequent to Spatter Dash SB scratch coat
Improving thermal resistance properties as well as sound dampening
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map