Heavy duty epoxy based floor screed from 5 to 35 mm thickness
Vetotop ES659 is a trowel applied floor screed composed of three part solvent-free combination of epoxy resin; modified amine hardener filled with specially graded chemically inert aggregates. The product performs in heavy duty demanding applications where abrasion and impact resistance are crucial factors in product choice.
Vetotop ES659 is supplied in 48 Kg Kit, Yield: 23.8 m²/kit @ 1mm thickness.
Vetoprime EP691 is supplied in 4 Liters Kit, Yield: 7-10 m2/ Liter
Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.
Original sealed bag of Vetotop ES659 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Vetotop ES659 is designed to be a hard wearing trowel applied epoxy screed on cementitious or metal substrates at thicknesses between 5 to 35 mm. The applied product will be resistant to water as well as a wide range of chemicals.
All surfaces receiving Vetotop ES659 should be primed with Vetoprime EP691 which is designed for maximum absorption and adhesion to concrete substrates. Add the entire contents of the hardener tin to the base tin and mix the two primer components thoroughly for at least 2 minutes - only mix full packs. Once mixed, the primer should be applied immediately to the prepared substrate using stiff brushes and/or rollers. The primer should be well ‘scrubbed’ into the substrate to ensure full coverage, but care should be taken to avoid over application or ‘ponding’. Allow the primer to become tacky before proceeding to the next stage. Porous substrates may require a second primer coat - when the first coat is directly absorbed into the substrate - but minimum over-coating times must still be observed.
Vetotop ES659 is supplied in three pre-weighed packs (base, hardener and aggregate) which are ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both performance and appearance of the finished floor. Mixing should be carried out using either a forced action mixer; or a heavy duty mobile mixer fitted with a suitable jiffy type mixing paddle. All such equipment should be of a type and capacity approved by Saveto. The components should be mixed in a suitably sized mixing vessel. Stir the base and hardener components individually then empty them into the mixing vessel scrapping the edges and mix for 2 minutes. The contents of the graded aggregate pack should be slowly added and mixing carried out for a further 3 minutes until a completely homogeneous material is obtained.
Application starts 20min after primer application (at 23C) while the primer is still tacky. Vetotop ES659 should be spread to uniform thickness on the primed surface using either a screed box or the edge of a steel trowel. The material should be tamped with a steel float to ensure complete compaction and finally finished to a closed even texture using a steel trowel. Screeding rods are useful to maintain a minimum compacted thickness of 3 mm. The material must be applied within the pot life after mixing.
Vetotop ES659 can be used to form perimeter edge coving up to a height of 50 mm. Skilled applicators can also use it to repair stair treads and fix expansion joint edges.
Although Vetotop ES659 is impervious at 5 mm thick in constantly wet operations areas or where a high degree of cleanliness is required, the Vetotop ES659 may be sealed with Vetotop EC698.
Vetotop ES659 must be at least 3 days old and high spots such as trowel marks rubbed down.
All tools and equipment should be cleaned immediately after use with Vetonit Solvent XX600.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range. New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Vetotop ES659 is non flammable. Refer to product material safety data sheet for information.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Solvent based high performance, self priming, thin epoxy topping
High strength fine structural repair mortar