High performance gun grade firestop, silicone neutral, silicone sealant.
Vetoflex SS789 is a single component high performance gun grade fire-stop weather sealant based on fire resistant Silicone formulation. The sealant is suitably formulated by using special additives and chemicals. The product is fire resistant, easy to apply and seals joints between construction parts subjected joint movement.Vetoflex SS789 helps to protect combustible and non-combustible penetrations for up to 4 hours fire rating. This product can be used for sealing all movement joints up to 50% and restricts the passage of fire and smoke from room to room and to escape routes. Since the sealant is low VOC, it is user friendly and confirms to green building requirements.
Vetoflex SS789 is supplied in 280 mL cartridges, Coverage: 40-45 linear cm @ width & depth of 25mm
stated consumptions data are for general guidance.
Original sealed container of Vetoflex SS789 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Vetoflex SS789 should be carefully applied using a mastic gun, ensuring that the material is forced well into the gap to obtain the correct joint and achieve good adhesion between surfaces. Necessary tooling to be done within 5 minutes after application
Vetoflex SS789 should be removed from tools, equipment and mixers with Vetonit Solvent XX400 immediately after use. Hardened material can only be removed mechanically.
Clean all joint surfaces and remove any dust, unsound material, plaster, oil, paint, grease, corrosion deposits or algae. Roughen the surfaces, remove any laitence and expose aggregate by light scabbling or grit-blasting.
Oil and grease deposits should be removed by steam cleaning, detergent scrubbing or the use of a proprietary degreaser.
Any joint filler must be checked to ensure it is tightly packed and no gaps or voids exist at the base of the sealing slot before positioning a bond breaker.
The use of a bond breaker is not required in expansion joints containing cellular polyethylene joint filler, backing rod (Vetoflex PBR). For contraction joints a bond breaker tape or back-up strip must be used.
Where a particularly neat finish is required, mask the face edges of the joint before sealing and remove immediately after tooling is completed.
Vetoflex SS789 should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well ventilated areas. In case of insufficient ventilation wear suitable respiratory protection.
Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection.
Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.
For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safety-related data.
Vetoflex SS789 is non flammable at ambient conditioin.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Closed cell polyethylene backing rod
Multi-component polyurethane joint sealant
(Formerly known as Saveto PU2)
Two-component polysulphide trafficable joint sealant
(Formerly known as Saveto PS2)
High performance, elastomeric, single component polyurethane sealant
(Formerly known as Saveto PU1)
Two-component trafficable, jet fuel resistant heavy duty pitch modified polyurethane sealant
High performance, aromatic & flexible waterproof polyurethane flooring membrane