Primers and Ancillary
Vetonit Plastering Bond

Bonding agent & admixture for render & plaster

Uses
Works as admixture with plaster, lime/sand cement screeds, renders, and cement based mortars.
Works as bonding agent and can be sprayed or brushed on green substrates to improve bonding of plasters, patching compounds. Renders, mortars, joint tape fixing etc.
Can be used for both internal and external applications.
Fast Download
Technical Information
Product Description

Plastering Bond is a single component polymer based, bonding agent for cementitious materials. It is a water based, specially formulated to enhance bonding properties as well as improve mechanical strengths of plaster mixes when incorporated with mixing water. Plastering Bond also reduces shrinkage cracks during early stages of cement hardening by minimizing surface water loss in fresh applied mixes. Plastering Bond is ideal for use with Render and Plaster mixes. Plastering Bond is supplied as ready to use on site without any dilution for desired applications.

Advantages
  • Multipurpose usage.
  • Can be used as bonding agent & admixture.
  • Enhances bonding of plaster, sand/cement screed, renders etc.
  • Improves hydration & curing when added to cement based mixes.
  • Improves compression strength & abrasion.
  • It adheres well to various construction materials, including concrete, stone, etc.
  • Ensure brighter & long lasting colour to architectural finishes.
  • Reduces shrinkage & cracks.
Compiliance Standard
  • ASTM C932
  • BS 6319
Packaging & Coverage

Vetonit Plastering Bond is supplied in 20 Liter Containers, Theoretical Coverage: 4 - 6 m²/Ltr as bonding agent

Shelf Life & Storage

Original sealed container of Vetonit Plastering Bond has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Plastering Bond is non-flammable.

Colors
Milky white liquid
Application Information
Instructions for use

Application
It is recommended to mix the material in same container prior to use.
Follow the Plastering Bond addition rates as specified by consultant or contractors required for each type of premixed mortar.

As Admixture
Plastering Bond can be used as total or partial replacement of gauging water required for plaster & render mixes.
Add the Plastering Bond to pre-blended sand/cement based plaster, render, mortar, or other dry mixes. Mix for 3-4 min using mechanical mixer at low speed.
Let the mixture stand for 10 min and mix again briefly to achieve homogeneous lump free mixture.

As a Primer
Use neat Plastering Bond without dilution. Apply Plastering Bond using brush or spray directly onto substrate. If using hand pump, spray at a rate of 4-6 m2/litre.
While bonding agent is wet to tacky, follow immediately by applying plaster, screed, render, mortars etc.

Note: Vetonit Plastering Bond should remain tacky when applying top coat finishes.

Surface Preparation

Surface  must  be  well  cleaned  and  free  from  loose materials. Inconsistent parts, varnishes, grease, laitance, algae, must be eliminated through sand blasting or brushing before applying Plastering Bond.

Limitation

Use the whole material once you opened the pack, as the material start to skin & then dry. Any part material left in container must be kept air tight.
Do not mix with any additives or products unless recommended by saveto.
Tools should be cleaned with water before it hardens. After the hardening its residuals can be removed mechanically only.
For further information contact our technical department.

Additional Information
Health & Sefety

Vetonit Plastering Bond is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise.
Ensure adequate ventilation when using the material and avoid inhalation of vapours.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond

Multi-purpose bonding agent & admixture

Saveto Bond 2

Multipurpose low viscosity bonding agent & admixture

Saveto PP Fiber

High Quality Monofilament Polypropylene Fibers

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

view more
Featured Product
Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Uses
Waterproof lining for swimming pools, water tanks, dams, canals, etc.
Wet-areas waterproofing while receiving tile adhesives and other renders.
Protecting concrete and masonry structures against ingress of chloride ions and carbonation.
As a crack isolation membrane in tile fixing assemblies.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map