Plasters & Renders
Premix Plaster M

Manual Applied Premixed Plaster

Internally or externally in wet & dry conditions onto block walls & rough surfaces.
Applied on vertical and over-head concrete surfaces that are smooth and also precast concrete surfaces subsequent to the application of a spatter dash coat, Spatter Dash SB is recommended for this application.
Ceramic tiling can be fixed directly on the Premix Plaster M.
Fast Download
Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
Technical Information
Product Description

Premix Plaster M is a cement based plastering material composed of hydraulic binders, selected graded sand, aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only the addition of clean water to produce cohesive mortar. Premix Plaster M is a high quality product contains special shrinkage control additive. It is designed for manual hand application for areas that can not be accessed by machine application. Premix Plaster M is generally applied in thicknesses ranging from 5 to 20 mm per layer.

  • Factory controlled pre-blend ensures consistent high quality.
  • Requires only addition of water on-site at the time of usage.
  • Uniform colour/mass.
  • Improved workability & curing.
  • Easy application with uniform work flow enables high productivity & superior finishing.
  • Strong adhesion on variety of substrates.
  • Internal & external applications.
  • Weather resistant.
  • Shrinkage control reduces surface cracks.
  • Suitable for humid & dry conditions.
Compiliance Standard
  • BS:EN 998-1:2003
  • ASTM C348, C349
  • ASTM C150 Type 1
  • ASTM C 926 
Packaging & Coverage

Premix Plaster M is supplied in 50kg Bag, with coverage: 1.3 - 1.5 Kg / m2 / mm thickness

Shelf Life & Storage

Original sealed bag of Premix Plaster M has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place. Premix Plaster M is non-flammable. 

Grey color.
Application Information
Instructions for use

For manual mixing add to the mixing container 8-10 litres of water for each 50 Kg bag of Premix Plaster M. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Hand mixing is allowed for small batch quantities by mixing for approx. 1-2 min or when homogenous mix is achieved. Mixed material must be used within 90 min. Do not add water to the mix once the mixed mortar start to harden.

Premix Plaster M can be applied in a single or two layers on rough or smooth surfaces to achieve the desired thickness. Apply Spatter Dash SB prior to the application of Premix Plaster M.
Apply mixed material using hawk & trowel technique. Rod or level to a uniform thickness of 5-20 mm. Immediately then follow smoothing the material to achieve the desired appearance.
For second layer allow the first layer to partially set (60-120min depending on weather). Apply second layer at thickness of 5-20 mm as described above.
After the surface appears stiff but still moist, follow the smoothing the material to achieve a desired appearance.
Plaster Mix M can be applied to ceiling with maximum thickness of 15mm.

Premix Plaster M is best cured by spraying water on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, etc.
Prior to Premix Plaster M application, soak the entire surfaces with clean potable water. Surface should be dry at the time of Premix Plaster M application.

  • Do not mix with any additives or products unless recommended by Saveto. Make sure the substrate is suitable for plaster application. In case of doubt, try on sample area to assess its suitability or consult a Saveto representative.
  • Do not apply the product at a temperature lower than +5ºC. During summer season the working area must be covered to prevent ill-effects of direct sun and also excessive air-draught during initial curing stage.
  • Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
Additional Information
Health & Sefety

Premix Plaster M is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic PLASTER

High quality light weight premixed acoustic plaster

Plaster Gypsum

High quality light weight gypsum plaster

Plaster Gypsum PERLITE

Thermal insulation llight weight gypsum perlite plaster

Plaster Cement PERLITE

Sprayable premixed plaster

Premix Plaster S

Sprayable premixed plaster

view more
Featured Product
Spatter Dash S

Weather resistant premixed cementitious scratch coat

Internal & external in wet & dry conditions.
On block walls, fair-faced concrete and precast panels prior to plastering application.
Plaster bond enhancer and mechanical key on horizontal, vertical and overhead application.
Enhances the binding between substrate & plasters or coatings.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map