Flooring & Coatings Systems
Vetotop UC175

UV resistant, matt finish easy to clean waterbased polyurethane wall coating

Uses
High abrasion resistant walls.
Interior and exterior applications.
Institutional and high traffic areas
Fast Download
Technical Data Sheet
download (*.pdf 0.22Mb)
Catalogues
Flooring Technical Brochure
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop UC175 is a clear two component, low VOC water based  UV resistant urethane sealer. It is used as UV resistant sealer over masonry, concrete, gypsum and various decorative finishes. The material has excellent adhesion to minimally profiled concrete. Vetotop UC175 is UV stable for use in exterior applications, cures rapidly and the sealed system is ideal for all weather exposure. When used as a finish coat, Vetotop UC175 gives a hard, matt surface that offers excellent stain resistance and easy cleanability. Vetotop UC175 is supplied in a pack size of 4 litre kit consist of Resin & Hardener.

Advantages
  • Excellent adhesion.
  • UV Resistant - does not yellow.
  • Good chemical resistance.
  • Durable and low maintenance cost.
  • Excellent resistance to a wide range of mild chemicals.
  • Tough with excellent impact and abrasion resistance.
  • Elastomeric.
  • Odorless.
Compiliance Standard

- BS 7976-2
- ASTM D 638
- BS 3900

Packaging & Coverage

Vetotop UC175 is supplied in 4 Liter Kits, Theoretical Coverage 2.5-5.0 m2 / Liter / coat

Vetoprime AP180 is supplied in  5 Liter Jerrycan,  Theoretical Coverage 4-10 m2 / Liter / coat

Shelf Life & Storage

Original sealed kit of Vetotop UC175 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Colors
Vetotop UC175 is available in clear colour and can be produced in any RAL upon request subject to minimum quantities.
Application Information
Instructions for use

Mixing Vetotop UC175


In a separate plastic mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners or water at any time.

Let the mixed material remain in covered container for 5-7 minutes. Mix for 1 minute and sieve into another clean plastic container. Always rinse the used containers with water prior to use.

Application

Apply Vetotop UC175 by roller or brush to the surface. The application should be at a rate of 2.5-5.0 m2 /liter per coat.
Application should not be carried out when humidity exceeds 85% or drops below 15%, or when the surface temperature to be coated is less than 3°C above the dew point.

Do not apply in direct sunlight or when ambient temperatures are above 40°C or below 7°C.

Cleaning

Tools and equipment should be cleaned with clean potable water immediately after use.

Surface Preparation

Surface Preparation


The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc.
Laitence and weak surface layer shall be removed using mechanical methods such as grinding in order to provide a sound well profiled surface. All necessary repairs should be made prior to application.
New concrete shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Substrate Priming

Vetotop UC175 can be applied directly to most sound surfaces. However, if the surface is highly absorbent or powdery in nature; then priming is recommended using Vetoprime AP180.

Limitation

Design Criteria

Vetotop UC175 is designed to be applied by roller or brush as a single coat. The product is designed to resist ultraviolet rays (UV) while being cleanable and abrasion resistant.

Additional Information
Health & Sefety

Vetotop UC175 is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise.
In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetotop UC175 and Vetoprime AP180 are nonflammable. Refer to product(s) MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

 

More Products from this section
Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

view more
Featured Product
Plaster Mix M

Manual Applied Premixed Plaster

 

Uses
Designed for manual or hand application.
Internally or externally in wet & dry conditions onto block walls & rough surfaces.
Ceramic tiling can be fixed directly on the Premix Plaster M.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map