Flooring & Coatings Systems
Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Leveling of concrete slabs prior to application of final floor coverings such as tiles and resinous systems.
As a substrate for vinyl tiles, parquet, carpet and floor coverings that require super-flat substrates.
Fast Download
Flooring Technical Brochure
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop CL530 is a single component cementitious floor self leveling underlayment composed of hydraulic binders, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, once mixed it will form a cohesive self smoothening honey-like flowing mortar that is applied in thicknesses between 2 and 10 mm giving a super flat finish ready to receive final floor coverings including tiles, carpets, resinous flooring systems, parquet, ...etc.

  • Factory controlled pre-blend ensures consistent high quality.
  • Suitable for Middle East harsh weather conditions.
  • Easy application enabling high productivity & superior finishing.
  • Rapid commissioning and serviceability.
  • High bond to substrate.
  • Excellent physical and mechanical properties.
  • Shrinkage compensated.
  • Excellent workability.
  • Fiber reinforced resisting crack formation.
Compiliance Standard
  • EN197: 2011
  • EN16236:2013
  • EN13813:2002
  • BS8204:2010
Packaging & Coverage

Vetotop CL530 supplied in 25 Kg / Bag. Yield - 1.5 - 1.8 Kg/m²/mm.

Shelf Life & Storage

Original sealed bag of Vetotop CL530 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Grey Colour
Application Information
Instructions for use


For single bag mixing add to the mixing container 4.6 - 4.8 liters of water for each 25 Kg bag of Vetotop CL530. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3 - 4 minutes, until a uniform, lump-free consistency is achieved.
Try to minimize the water addition to get higher strength. Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.
Vetotop CL530 can be applied using screw type pump with pumping rate of 25-50 liters/min and length of hose 40-50 LM. and control the water dosage to achieve the required flow.
After placing onto the primed surface, apply by trowel or pin screed. Rake to the Vetotop CL530 spreads and adjust itself to a level floor.
For small areas Vetotop CL530 can be applied manually.
It is advised to spike roll in two directions immediately after application to release entrapped air.


The product is a self-curing product and should be left undisturbed for 3 to 5 days prior to use of subsequent toppings.

The applied product should be protected from environmental agents such as wind, direct sunlight, dirt and dust exposure to insure smooth leveled hard surfaces for at least the first 24 hrs.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc.
Larger areas can be divided with wooden battens to control the pumping volume and determine the layer thickness to be applied.

Prime the surface with Vetoprime PB433 diluted with potable water (ratio of 1:1.5). Mix thoroughly and spray or brush onto the floor without pooling. Its important to note that if the primer dried it will become a debonding layer and - thus make sure to apply the material within the primer open time. Allow the primer coat to be tacky when applying Vetotop CL530. Alternatively where large areas are to be applied, prime the floor with Vetobond EB431 which will allow for long open time.

  • Do not mix with any additives or products, unless recommended by Saveto.
  • Make sure the substrate is suitable for underlayment application. In case of doubt, try on sample area to assess its suitability.
  • Vetotop CL530 is not an abrasion resistant nor recommended to forklift or heavy loads.
  • Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from
  • direct sun and also air-draft during initial curing stage.
  • Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
  • For further information contact our technical department.
Additional Information
Health & Sefety

Vetotop CL530 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.

Vetotop CL530 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

Vetotop EC495

Solvent based high performance, self priming, thin epoxy topping

view more
Featured Product
Vetogrout CG519

Universal cementitious grout for large thickness repair & grouting

Precast panels wall and base segment grouting
Repair of broken structural concrete elements where large segments are of concern.
Casting structural members and elements where conventional grouts can not perform.
Base plate grouting where sections are in excess of 70 mm.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map